Towels needed three rounds and the laundry room steamed up. Our duct runs through the attic to the roof and it was stuffed with lint. One cycle does it now.
Denim still clammy after an hour, zero heat, or a screech the second you hit start. Lots of homes here push dryer exhaust up through a hot attic, so we inspect the full duct as well as the heater, belt and rollers.

We Fix
Pull the folder that matches what's happening at home. Inside you'll find the likely cause, what to do in the meantime, and the parts we check first.
Tumbles But Never Heats
Symptom: drum rotates on schedule, clothes come out cold and wet.
Usual cause: a burned-through coil or popped safety fuse on electric models; a weak igniter or tired valve coils on gas.
Our fix: meter each component so only the dead one gets replaced.
While You Wait
Peek at the breaker box for a two-pole breaker with half tripped; electric dryers spin without heat on one leg. Gas owners: valve handle parallel to the pipe means open.
Usual Suspects
One Load, Two Or Three Cycles
Symptom: one basket now needs a second or even third round.
Usual cause: lint packed along a long vent run, especially ducts that climb through a sweltering attic to a roof cap.
Our fix: clean the run end to end and confirm a strong exhaust where it exits the house.
While You Wait
Wash the lint screen with dish soap, then go outside mid-cycle; you should feel a firm breeze at the vent.
Usual Suspects
Motor Runs, Drum Stays Still
Symptom: the motor hums while the drum sits motionless.
Usual cause: a snapped belt, a seized idler, or rollers worn flat.
Our fix: open the cabinet, confirm which, and replace worn neighbors at the same time.
While You Wait
Rotate the drum by hand. No resistance at all usually means a broken belt, so stop pressing start.
Usual Suspects
Shrieks At Start-Up
Symptom: a shrill squeal at start-up or a thump with each revolution.
Usual cause: idler pulleys running dry and rollers developing flat spots.
Our fix: replace them as a pair so a second noise doesn't appear weeks later.
While You Wait
Listen for when it begins; noise from the very first second tends to be the pulley, noise after warm-up the rollers.
Usual Suspects
Shuts Off Before Clothes Are Dry
Symptom: it quits partway while clothes are still damp.
Usual cause: restricted exhaust overheats the cabinet and trips a safety thermostat, or waxy softener residue blinds the moisture sensor.
Our fix: clear the airflow, clean the sensor bars, test both thermostats.
While You Wait
After clearing the vent, wipe the two metal bars inside the door opening with rubbing alcohol.
Usual Suspects
Hot Or Scorched Smell
Symptom: a hot, dusty smell during a cycle.
Usual cause: fluff collecting around the heater box or behind the drum, out of reach of the screen.
Our fix: open the cabinet and vacuum everything out, removing a genuine fire hazard.
While You Wait
Unplug it until a tech has looked inside; the dangerous lint is the lint you can't see.
Usual Suspects
Every major make in Cedar Park kitchens and laundry rooms, from builder-grade basics to high-end ranges.









Every manufacturer has its own code list, so each entry shows the brand it belongs to. Use them as a clue rather than a verdict.
| Code | Brand | What It Means |
|---|---|---|
| d95 | LG | LG exhaust nearly blocked; clean the duct first. |
| nP | LG | LG heater has no supply voltage. |
| tE1 | LG | LG temperature sensor open or shorted. |
| HC | Samsung | Samsung overheating, typically choked airflow. |
| AF | Whirlpool | Whirlpool airflow warning; inspect screen and duct. |
| PF | Whirlpool | Whirlpool power blip mid-cycle; press start. |
Should that code reappear once the vent is clear and power is cycled, book a technician to track it down.
What Cedar Park homeowners said after their dryer was fixed.
Towels needed three rounds and the laundry room steamed up. Our duct runs through the attic to the roof and it was stuffed with lint. One cycle does it now.
Dead cold. Fuse blown from a clogged vent. Both sorted in one trip.
Drum wouldn't budge. New belt and rollers in one go.
Screech on every start. Pulley ordered, two visits, silent now.
Gas model quit heating. Igniter and coils swapped within the hour.
Hot dusty smell. He vacuumed lint out from around the heater box.
Start with airflow; it's the usual suspect and easy to inspect.
Try These First
Clean the lint screen
Clean it every single load.
Check the outside vent
Warm air should push the outside flap open.
Look behind the dryer
Look for a crushed foil duct behind the cabinet.
Check both breakers
Both halves of the dryer breaker must be on.
Don't overload it
Half-full drums dry faster than stuffed ones.
Open the gas valve
Gas models: supply handle parallel to the pipe.
Still slow or cold? Book a visit and we'll sort it out.
Leave your details on the clipboard and we'll ring you back to line up a time. Mention the make and the symptom when we call so the right parts ride along.
Prefer to talk? (512) 643-8158Service Request
Three fields and you're done.
Thank You!
Your message has been sent successfully. We'll get back to you shortly.
Thank You!
Your message has been sent successfully. We'll get back to you shortly.
We cover every corner of Cedar Park and the edges of Leander next door. If your neighborhood isn't on a sign below, call anyway; chances are we're out that way most days.